1959 -1964 Impala and Biscayne Power Steering Conversion & Bump Steer Kit Part # ST-5964

If you are looking for a kit to fix the steering problems for 1959, 1960, 1961, 1962, 1963, 1964 Impala, El Camino, Biscayne, and 58 if you want to do a spindle and steering knuckle change we have it. Bump steer is a problem with these older cars and the majority of the problem is the factory steering system. If you are looking at this kit you would already have purchased a Borgeson steering box. You have either installed the kit or about to. Borgeson has a plate bolted to the side of the steering box that gets replaced by our steering box mount. You must change it out. The pitman arm, center link (also called a drag link), tie rods, idler and a couple other components also get changed. This kit does not include a front sway bar. The factory sway bar will no longer work. You must use a sway bar that attaches to the frame before the steering box (closer to the radiator). Our sway bar SB-5864G is designed to do that. If you have a different sway bar that does bolt before the steering box you should be in good shape.

The steering box (Borgeson) is an integral 14:1 so you will only need two power steering hoses, pressure and return, not four. Note: Other power steering boxes will not work with this kit. The factory power ram is no longer required. This also means the pivot ball assemble on the factory center link at the pitman arm will no longer apply. The spring loaded pivot ball assemble at this location is no longer required. Our conversion kit eliminates the spring loaded ball and converts it over to a newer style center link that is more like a ball joint. When installing the Borgeson box clearance to the radiator will be your main concern. If you run into this problem there are aftermarket radiators that are built to fit the larger steering boxes. Here at Global West we are working on radiators for various applications.

One advantage using this steering box is with the new linkage, we are able to have the box centered internally. This combination means left and right turns have the same turning radius.

The center link as seen in the photo has a relocation bar attached to it that sets up the correct steering geometry for the system. Note: The factory center link if used will never have the correct bump. We ship the assembly complete ready to install.

Spindles: The stock spindle for a 59-64 Impala or a dropped spindle will work provided the steering knuckle arm is in the same location as stock. We have 2 inch drop spindles for 58-64 Impala that except a Wilwood brake system. We can install up to a 14 inch disc brake.

1958 Impala - uses a different spindle and steering knuckle arm, for proper bump steer our kit requires you to use a 59-64 steering knuckle and spindle on your 58. The combination will bolt up with no trouble.

The steering system basically bolts in except for relocating the sway bar and possibly drilling a 3/8 hole for the idler arm. This kit is pretty much straight forward. Once you have installed the system you will require a alignment.

This kit includes:

• A special mounting bracket that sets the angle of the steering box for the correct geometry
• idler arm
• Ball joint-type center link
• Inner tie rods
• Tubular tie rod adjusting sleeves
• Outer tie rods
• Center link relocation bar
• Pitman arm
• Intermediate steering shaft

Tech Info: What is bump steer?

Bump steer is when the suspension moves up and down and one or both wheels point on their own a different direction without you turning the steering wheel. This is caused by incorrect angles between the suspension control arms and the steering linkage. Watch the videos below and you can see the change in the toe settings. The toe is the direction the tires are pointing. If the tire points other than straight when the suspension moves up or down without you turning the steering wheel, the car will have a tendency to wander over bumps and during body roll. Many people believe it is just the way old cars drive, but the condition can be fixed with this simple bolt on kit.

See Global West tech videos that show what bump steer is doing using the factory steering linkage and what it does after the new kit is installed.

Why 1958 through 1964 Impalas wander (Bump Steer)-Part 1



Impala Bump Steer Check using Aftermarket Steering-Part 2



Impala Bump Steer: The Final Result