Toll Free 1 (877) 470-2975
1974-81 Camaro Tubular Subframe Connectors Part #902
1970-81 Subframes, Body Mount Bushings
1974-81 Camaro Tubular Subframe Connectors Part #902
GM subframe connectors No cutting or modification of floor pans required.The subframe connectors are full length. This means the subframe connector is going to the back of the factory subframe and extend to the rear structural support rail going over the differential. The subframe connector is welded to the uni-body portion of the chassis, not bolted. The subframe connectors do not attach to the leaf spring front bracket bolts. Those bolts are 3/8 of an inch in diameter and are held in place with small nut clips and will not hold up. The subframe connector sandwiches between the factory frame and the body. It can be bolted or welded. Welding is always the best but in this case it is not as practical. If the car is in a collision, the frame needs to be replaced by unbolting the subframe: bolting to the original frame works because the material of the factory frame is 3/16” thick, all the sides are being bolted. Interloc body mount bushings should be used if subframes are installed. They compliment the subframes objective. Two bushings are included with subframe connectors. Use part #809, #819 or #816 for remaining bushings. Subframes are powder coated black Subframes are made from 1 5/8 x 0.125 wall DOM tubing Additional hardware and plates are supplied. No exhaust modifications are required. Minimal ground clearance lost (in most cases the exhaust is lower)
https://www.globalwest.net1974-1981-camaro-tubular-subframe-connectors-global-west.html
$275.25
GM subframe connectors
No cutting or modification of floor pans required.The subframe connectors are full length. This means the subframe connector is going to the back of the factory subframe and extend to the rear structural support rail going over the differential. The subframe connector is welded to the uni-body portion of the chassis, not bolted. The subframe connectors do not attach to the leaf spring front bracket bolts. Those bolts are 3/8 of an inch in diameter and are held in place with small nut clips and will not hold up. The subframe connector sandwiches between the factory frame and the body. It can be bolted or welded. Welding is always the best but in this case it is not as practical. If the car is in a collision, the frame needs to be replaced by unbolting the subframe: bolting to the original frame works because the material of the factory frame is 3/16” thick, all the sides are being bolted. Interloc body mount bushings should be used if subframes are installed. They compliment the subframes objective. Two bushings are included with subframe connectors. Use part #809, #819 or #816 for remaining bushings.
Subframes are powder coated black
Subframes are made from 1 5/8 x 0.125 wall DOM tubing
Additional hardware and plates are supplied.
No exhaust modifications are required.
Minimal ground clearance lost (in most cases the exhaust is lower)
No cutting or modification of floor pans required.The subframe connectors are full length. This means the subframe connector is going to the back of the factory subframe and extend to the rear structural support rail going over the differential. The subframe connector is welded to the uni-body portion of the chassis, not bolted. The subframe connectors do not attach to the leaf spring front bracket bolts. Those bolts are 3/8 of an inch in diameter and are held in place with small nut clips and will not hold up. The subframe connector sandwiches between the factory frame and the body. It can be bolted or welded. Welding is always the best but in this case it is not as practical. If the car is in a collision, the frame needs to be replaced by unbolting the subframe: bolting to the original frame works because the material of the factory frame is 3/16” thick, all the sides are being bolted. Interloc body mount bushings should be used if subframes are installed. They compliment the subframes objective. Two bushings are included with subframe connectors. Use part #809, #819 or #816 for remaining bushings.
Subframes are powder coated black
Subframes are made from 1 5/8 x 0.125 wall DOM tubing
Additional hardware and plates are supplied.
No exhaust modifications are required.
Minimal ground clearance lost (in most cases the exhaust is lower)
1974-81 Camaro Tubular Subframe Connectors Part #902
Product Description
GM subframe connectors
No cutting or modification of floor pans required.The subframe connectors are full length. This means the subframe connector is going to the back of the factory subframe and extend to the rear structural support rail going over the differential. The subframe connector is welded to the uni-body portion of the chassis, not bolted. The subframe connectors do not attach to the leaf spring front bracket bolts. Those bolts are 3/8 of an inch in diameter and are held in place with small nut clips and will not hold up. The subframe connector sandwiches between the factory frame and the body. It can be bolted or welded. Welding is always the best but in this case it is not as practical. If the car is in a collision, the frame needs to be replaced by unbolting the subframe: bolting to the original frame works because the material of the factory frame is 3/16” thick, all the sides are being bolted. Interloc body mount bushings should be used if subframes are installed. They compliment the subframes objective. Two bushings are included with subframe connectors. Use part #809, #819 or #816 for remaining bushings.
Subframes are powder coated black
Subframes are made from 1 5/8 x 0.125 wall DOM tubing
Additional hardware and plates are supplied.
No exhaust modifications are required.
Minimal ground clearance lost (in most cases the exhaust is lower)
No cutting or modification of floor pans required.The subframe connectors are full length. This means the subframe connector is going to the back of the factory subframe and extend to the rear structural support rail going over the differential. The subframe connector is welded to the uni-body portion of the chassis, not bolted. The subframe connectors do not attach to the leaf spring front bracket bolts. Those bolts are 3/8 of an inch in diameter and are held in place with small nut clips and will not hold up. The subframe connector sandwiches between the factory frame and the body. It can be bolted or welded. Welding is always the best but in this case it is not as practical. If the car is in a collision, the frame needs to be replaced by unbolting the subframe: bolting to the original frame works because the material of the factory frame is 3/16” thick, all the sides are being bolted. Interloc body mount bushings should be used if subframes are installed. They compliment the subframes objective. Two bushings are included with subframe connectors. Use part #809, #819 or #816 for remaining bushings.
Subframes are powder coated black
Subframes are made from 1 5/8 x 0.125 wall DOM tubing
Additional hardware and plates are supplied.
No exhaust modifications are required.
Minimal ground clearance lost (in most cases the exhaust is lower)
- 1974-81 Camaro Tubular Subframe Connectors Part #902
- 1970-1973 Camaro Tubular Subframe Connectors Part #901
- Solid Aluminum Interloc Body Mount Bushings (Stock Height) Part #800
- Solid Aluminum Interloc Bushings 1/2 in Drop Part #801
- Body Mount Bushings Kit used with Global West Sub frames Part #809 (recommended)
- Competition Engineering Subframe Interloc Body Mount Kit Part #818
Copyright © 2022 Global West Suspension Components Inc.